HARDVANES®
Wear check for vanes
Measure the height of your vacuum pump vanes and see the margin above your model’s minimum
- 312 records
- 10 brands
- Source cited for every model
HARDVANES® H95434 · 95 × 43 × 4 mmRenders created from textures of real product photographs
Wear reduces vane height H.
Not the length, not the thickness and not the bevel.
Check your vanes
312 records from ten brands. Choose your equipment or enter the dimensions from your unit’s manual.
Vane created from photographs of the HARDVANES® H95434 · height relative to your model’s new height; actual geometry depends on the part number
Explore the states or enter your vane measurement
How it is calculated
- Margin in millimetres
- Measured height − minimum height
- Margin as a percentage
- Margin in mm ÷ (new height − minimum height) × 100
Figures are shown rounded; the dimensional state is compared before rounding. The diagram is for guidance only. The percentage expresses height margin, not service hours or performance.
The text is selected so that you can copy it.
The new height is optional for checking the margin in millimetres. Add it from the manual or the spare-part data sheet for your variant to get the percentage as well.
Relative height comparison. The example does not change your measurement
The result compares heights. A positive margin does not validate the condition of the vanes or allow their service life to be estimated. Complete the inspection of the faces, edges and clearance specified in the manual
Find model and view sourcesMeasure between edges
Height H is measured between the two long edges. Confirm this dimension on the drawing in your manual
Digital caliper · example of a set of seven
- P135.62
- P235.58
- P335.50
- P435.61
- P535.48
- P635.57
- P735.60
Enter the lowest reading, without averaging: 35.48 mm
- Check the nameplate
Identify the full model, variant and serial number. Check that the manual and the vane material match that unit
- Measure with a caliper
Prepare the work as the manual specifies: shutdown, isolation, start-up lockout, cooling down and release of residual pressure or vacuum. Then measure the height of each vane with a caliper
- Use the lowest height
Record every measurement and use the lowest, without averaging or rounding up. If any reaches or falls below the minimum, replace the set as the manual specifies
Detail matters too
Height is one part of the check. Inspect the faces, the edges and every vane in the set
Check for cracks, chipping or uneven wear. Apply the inspection criteria in your manual, even if the height is above the minimum
Inspect every piece. The lowest height in the set is the one to enter for comparison with your model’s limit
Models and sources
312 records of dry-running rotary-vane pumps and compressors. Search by model or spare-part number.
View the sources| Brand | Model | New height · mm | Minimum · mm | Select model |
|---|---|---|---|---|
| BECKER | DT 3.10Ref. 90132700007 | 27 | 18 | |
| BECKER | DT 3.25Ref. 90134900007 | 43 | 28 | |
| BECKER | DT 3.40Ref. 90135200007 | 43 | 28 | |
| BECKER | DT 4.2Ref. 90138700005 | 16 | 11 | |
| BECKER | DT 4.4Ref. 90138700005 | 16 | 11 | |
| BECKER | DT 4.6Ref. 90138800005 | 18.5 | 12.5 | |
| BECKER | DT 4.8Ref. 90138800005 | 18.5 | 12.5 | |
| BECKER | DT 4.10Ref. 90132700007 | 27 | 18 | |
| BECKER | DT 4.16Ref. 90134700007 | 35 | 21 | |
| BECKER | DT 4.25Ref. 90134900007 | 43 | 28 | |
| BECKER | DT 4.40Ref. 90135200007 | 43 | 28 | |
| BECKER | DTLF 2.200Ref. 90136701005 | 65 | 41 | |
| BECKER | DTLF 2.250Ref. 90136701005 | 65 | 41 | |
| BECKER | DTLF 2.360Ref. 90132500005 | 64 | 41 | |
| BECKER | DTLF 2.400Ref. 90137301008 | 88 | 60 | |
| BECKER | DTLF 2.500Ref. 90137301008 | 88 | 60 | |
| BECKER | DVT 3.60Ref. 90133000007 | 39 | 21 | |
| BECKER | DVT 3.80Ref. 90133000007 | 39 | 26 | |
| BECKER | DVT 3.100Ref. 90133300007 | 39 | 26 | |
| BECKER | DVT 3.140Ref. 90133400007 | 48 | 31 | |
| BECKER | DVX 3.140Ref. 90140500007 | 47 | 31 | |
| BECKER | DXLF 2.200Ref. 90132500005 | 64 | 41 | |
| BECKER | DXLF 2.250Ref. 90132500005 | 64 | 41 | |
| BECKER | DXLF 2.360Ref. 90132500005 | 64 | 41 | |
| BECKER | DXLF 2.400Ref. 90132510008 | 87 | 60 | |
| BECKER | DXLF 2.500Ref. 90132510008 | 87 | 60 | |
| BECKER | KDT 3.60Ref. 90133000004 | 39 | 21 | |
| BECKER | KDT 3.80Ref. 90133000004 | 39 | 26 | |
| BECKER | KDT 3.100Ref. 90133300004 | 39 | 26 | |
| BECKER | KDT 3.140Ref. 90133400004 | 48 | 31 | |
| BECKER | KVT 3.60Ref. 90133000004 | 39 | 21 | |
| BECKER | KVT 3.80Ref. 90133000004 | 39 | 26 | |
| BECKER | KVT 3.100Ref. 90133300004 | 39 | 26 | |
| BECKER | KVT 3.140Ref. 90133400004 | 48 | 31 | |
| BECKER | KVX 3.60Ref. 90140100004 | 37 | 21 | |
| BECKER | KVX 3.80Ref. 90140100004 | 37 | 26 | |
| BECKER | KVX 3.100Ref. 90140200004 | 37 | 26 | |
| BECKER | KVX 3.140Ref. 90132400004 | 47 | 31 | |
| BECKER | Picchio 2200Ref. 90133000004 | 39 | 31 | |
| BECKER | T 3.16 DSKRef. 90134700007 | 35 | 21 | |
| BECKER | T 3.25 DSKRef. 90134900007 | 43 | 28 | |
| BECKER | T 3.40 DSKRef. 90135200007 | 43 | 28 | |
| BECKER | T 4.10 DVRef. 90132700007 | 27 | 18 | |
| BECKER | T 4.16 DVRef. 90134700007 | 35 | 21 | |
| BECKER | T 4.25 DSKRef. 90134900007 | 43 | 28 | |
| BECKER | T 4.25 DVRef. 90134900007 | 43 | 28 | |
| BECKER | T 4.40 DSKRef. 90135200007 | 43 | 28 | |
| BECKER | T 4.40 DVRef. 90135200007 | 43 | 28 | |
| BECKER | VT 3.10Ref. 90132700007 | 27 | 18 | |
| BECKER | VT 3.16Ref. 90134700007 | 35 | 21 | |
| BECKER | VT 3.25Ref. 90134900007 | 43 | 28 | |
| BECKER | VT 3.40Ref. 90135200007 | 43 | 28 | |
| BECKER | VT 4.2Ref. 90138700005 | 16 | 11 | |
| BECKER | VT 4.4Ref. 90138700005 | 16 | 11 | |
| BECKER | VT 4.6Ref. 90138800005 | 18.5 | 12.5 | |
| BECKER | VT 4.8Ref. 90138800005 | 18.5 | 12.5 | |
| BECKER | VT 4.10Ref. 90132700007 | 27 | 18 | |
| BECKER | VT 4.16Ref. 90134700007 | 35 | 21 | |
| BECKER | VT 4.25Ref. 90134900007 | 43 | 28 | |
| BECKER | VT 4.40Ref. 90135200007 | 43 | 28 | |
| BECKER | VT 4.40/0-90Ref. 90139700007 | 41 | 33 | |
| BECKER | VTLF 2.200Ref. 90136701005 | 65 | 41 | |
| BECKER | VTLF 2.250Ref. 90136701005 | 65 | 41 | |
| BECKER | VTLF 2.250 SKRef. 90136701005 | 65 | 41 | |
| BECKER | VTLF 2.360Ref. 90132500005 | 64 | 41 | |
| BECKER | VTLF 2.400Ref. 90137301008 | 88 | 60 | |
| BECKER | VTLF 2.500Ref. 90137301008 | 88 | 60 | |
| BECKER | VX 4.10Ref. 90141300007 | 26 | 18 | |
| BECKER | VX 4.16Ref. 90141200007 | 34 | 21 | |
| BECKER | VX 4.25Ref. 90141000007 | 41 | 28 | |
| BECKER | VX 4.40Ref. 90140900007 | 41 | 28 | |
| BECKER | VXLF 2.200Ref. 90132500005 | 64 | 41 | |
| BECKER | VXLF 2.250Ref. 90132500005 | 64 | 41 | |
| BECKER | VXLF 2.400Ref. 90132510008 | 87 | 60 | |
| BECKER | VXLF 2.500Ref. 90132510008 | 87 | 60 | |
| BUSCH | DC 0025 CRef. 0722554302 | 44 | 33 | |
| BUSCH | DC 0040 CRef. 0722207620 | 44 | 33 | |
| BUSCH | DC 0063 BRef. 0722000016 | 44 | — | |
| BUSCH | DC 0080 BRef. 0722000017 | 44 | — | |
| BUSCH | SD 1005 CRef. 0722133118 | 26 | 23 | |
| BUSCH | SD 1008 CRef. 0722133118 | 26 | 23 | |
| BUSCH | SD 1010 BRef. 0722000242 | 27 | 20 | |
| BUSCH | SD 1010 CRef. 0722554297 | 36.5 | 27 | |
| BUSCH | SD 1016 BRef. 0722522489 | 35 | 27 | |
| BUSCH | SD 1016 CRef. 0722554298 | — | 27 | |
| BUSCH | SD 1025 BRef. 0722521014 | 36.5 | 27 | |
| BUSCH | SD 1025 CRef. 0722554302 | 44 | 33 | |
| BUSCH | SD 1040 BRef. 0722522488 | 44 | 33 | |
| BUSCH | SD 1040 CRef. 0722207620 | 44 | 33 | |
| BUSCH | SD 1040 DRef. 0722544213 | 44 | 33 | |
| BUSCH | SD 1063 BRef. 0722000016 | 44 | 33 | |
| BUSCH | SD 1080 BRef. 0722000017 | 44 | 33 | |
| BUSCH | SV 1003 DRef. 0722104640 | 19 | 14 | |
| BUSCH | SV 1005 CRef. 0722133118 | 26 | 23 | |
| BUSCH | SV 1005 DRef. 0722141943 | 22 | 17 | |
| BUSCH | SV 1008 CRef. 0722133118 | 26 | 23 | |
| BUSCH | SV 1010 BRef. 0722000242 | 27 | 20 | |
| BUSCH | SV 1010 CRef. 0722554297 | 36.5 | 27 | |
| BUSCH | SV 1016 BRef. 0722522489 | 35 | 27 | |
| BUSCH | SV 1016 CRef. 0722554298 | — | 27 | |
| BUSCH | SV 1025 BRef. 0722521014 | 36.5 | 27 | |
| BUSCH | SV 1025 CRef. 0722554302 | 44 | 33 | |
| BUSCH | SV 1040 BRef. 0722522488 | 44 | 33 | |
| BUSCH | SV 1040 CRef. 0722207620 | 44 | 33 | |
| BUSCH | SV 1040 DRef. 0722544213 | 44 | 33 | |
| BUSCH | SV 1063 BRef. 0722000016 | 44 | 33 | |
| BUSCH | SV 1080 BRef. 0722000017 | 44 | 33 | |
| Elmo Rietschle | DLT 6Ref. 513878 | 31 | 20 | |
| Elmo Rietschle | DLT 10Ref. 513455 | 31 | 20 | |
| Elmo Rietschle | DLT 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | DLT 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | DLT 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | KLT 10 | — | 20 | |
| Elmo Rietschle | KLT 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | KLT 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | KLT 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-DTA 60 | 52 | 38 | |
| Elmo Rietschle | V-DTA 80 | 52 | 38 | |
| Elmo Rietschle | V-DTA 100 | 52 | 38 | |
| Elmo Rietschle | V-DTA 140 | 52 | 38 | |
| Elmo Rietschle | V-DTE 3Ref. 522716 | 16 | 10 | |
| Elmo Rietschle | V-DTE 6Ref. 507051 | 15 | 10 | |
| Elmo Rietschle | V-DTE 8Ref. 523474 | 19 | 12 | |
| Elmo Rietschle | V-DTE 10Ref. 526315 | 18.5 | 12 | |
| Elmo Rietschle | V-DTN 6 | — | 20 | |
| Elmo Rietschle | V-DTN 10Ref. 513455 | 31 | 20 | |
| Elmo Rietschle | V-DTN 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-DTN 16Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-DTN 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-DTN 26Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-DTN 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-DTN 41Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-DTR 100 | 52 | 26 | |
| Elmo Rietschle | V-DTR 140 | 52 | 32 | |
| Elmo Rietschle | V-KTA 60Ref. 528802 | 52 | 38 | |
| Elmo Rietschle | V-KTA 80Ref. 523851 | 52 | 38 | |
| Elmo Rietschle | V-KTA 80/5Ref. 528401 | 43 | 38 | |
| Elmo Rietschle | V-KTA 100Ref. 523889 | 52 | 38 | |
| Elmo Rietschle | V-KTA 140Ref. 523885 | 52 | 38 | |
| Elmo Rietschle | V-KTN 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-KTN 16Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-KTN 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-KTN 26Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-KTN 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-KTN 41Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-KTR 100 | 52 | 26 | |
| Elmo Rietschle | V-KTR 140 | 52 | 32 | |
| Elmo Rietschle | V-VTA 60Ref. 5238510004 | 52 | 38 | |
| Elmo Rietschle | V-VTA 80Ref. 5238510004 | 52 | 38 | |
| Elmo Rietschle | V-VTA 100Ref. 5253510004 | 52 | 38 | |
| Elmo Rietschle | V-VTA 140Ref. 5266270004 | 52 | 38 | |
| Elmo Rietschle | V-VTE 3Ref. 522716 | 16 | 10 | |
| Elmo Rietschle | V-VTE 6Ref. 507051 | 15 | 10 | |
| Elmo Rietschle | V-VTE 8Ref. 523474 | 19 | 12 | |
| Elmo Rietschle | V-VTE 10Ref. 526315 | 18.5 | 12 | |
| Elmo Rietschle | V-VTN 6 | — | 20 | |
| Elmo Rietschle | V-VTN 10Ref. 513455 | 31 | 20 | |
| Elmo Rietschle | V-VTN 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-VTN 16Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | V-VTN 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-VTN 26Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | V-VTN 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-VTN 41Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | V-VTN 60Ref. 526577 | 47 | 37 | |
| Elmo Rietschle | V-VTR 100 | 52 | 26 | |
| Elmo Rietschle | V-VTR 140 | 52 | 32 | |
| Elmo Rietschle | VFT 25 | 27 | 22 | |
| Elmo Rietschle | VFT 40 | 27 | 22 | |
| Elmo Rietschle | VFT 60 | 34 | 25 | |
| Elmo Rietschle | VFT 80 | 40 | 30 | |
| Elmo Rietschle | VFT 100 | 40 | 30 | |
| Elmo Rietschle | VFT 140 | 55 | 40 | |
| Elmo Rietschle | VFT 180 | 55 | 40 | |
| Elmo Rietschle | VFT 250 | 55 | 40 | |
| Elmo Rietschle | VLT 6Ref. 513878 | 31 | 20 | |
| Elmo Rietschle | VLT 10Ref. 513455 | 31 | 20 | |
| Elmo Rietschle | VLT 15Ref. 513702 | 39 | 24 | |
| Elmo Rietschle | VLT 25Ref. 513431 | 39 | 24 | |
| Elmo Rietschle | VLT 40Ref. 518943 | 47 | 35 | |
| Elmo Rietschle | VLT 60Ref. 526577 | 47 | 37 | |
| Elmo Rietschle | VTB 180 | 69 | 40 | |
| Elmo Rietschle | VTB 250 | 69 | 52 | |
| Elmo Rietschle | VTB 340 | 91 | 57 | |
| Elmo Rietschle | VTB 500 | 91 | 57 | |
| ORION | CBXP8080Ref. 04106205010 | 51 | — | |
| ORION | KRA 8Ref. 04106205010 | 51 | — | |
| ORION | KRA 9Ref. 04106205010 | 51 | — | |
| ORION | KRF 15A-03Ref. 04101754010 | 34 | — | |
| ORION | KRF 25A-03Ref. 04100888010 | 38 | — | |
| ORION | KRF 40A-V-01Ref. 04100889010 | 40 | — | |
| ORION | KRF 70Ref. 04106205010 | 51 | — | |
| ORION | KRH 8Ref. 04106205010 | 51 | — | |
| ORION | KRS 3Ref. 04101754010 / 04009564010 | 34 | — | |
| ORION | KRS 5Ref. 04100888010 / 04009565010 | 38 | — | |
| ORION | KRX 3Ref. 04101754010 / 04009564010 | 34 | — | |
| ORION | KRX 5Ref. 04100888010 / 04009565010 | 38 | — | |
| DVP | SB 10Ref. 3301002 | 25 | 20 | |
| DVP | SB 10TVRef. 3301002 | 25 | 20 | |
| DVP | SB 12Ref. 3301002 | 25 | 20 | |
| DVP | SB 16Ref. 3301011 | 35 | 27 | |
| DVP | SB 25Ref. 3301016 | 42 | 32 | |
| DVP | SB 40Ref. 3301012 | 43 | 30 | |
| DVP | SC 5Ref. 3301024 | — | 21 | |
| DVP | SC 8Ref. 3301029 | — | 18 | |
| DVP | SC 8TV | — | 18 | |
| DVP | SC 16Ref. 3301016 | 42 | 27 | |
| DVP | SC 25Ref. 3301016 | 42 | 32 | |
| DVP | SC 40Ref. 3301012 | 43 | 30 | |
| DVP | SC 60Ref. 3301020 | 46 | 33 | |
| DVP | SC 80Ref. 3301020 | 46 | 34 | |
| DVP | SC 100Ref. 3301021 | 46 | 33 | |
| DVP | SC 140Ref. 3301021 | 46 | 34 | |
| GAST | 0211Ref. AA348A | — | 13.890625 | |
| GAST | 0322Ref. AF109C | — | 15.08125 | |
| GAST | 0323Ref. AH850A | 32.2 | 15.875 | |
| GAST | 0332Ref. AD447 | — | 6.35 | |
| GAST | 0333Ref. AD447 | — | 6.35 | |
| GAST | 0522Ref. AF109C | — | 15.875 | |
| GAST | 0523Ref. AH850A | 32.2 | 19.84375 | |
| GAST | 0821Ref. AB992B | — | 26.19375 | |
| GAST | 0822Ref. AB992B | — | 26.19375 | |
| GAST | 0823Ref. AK513 | 38 | 22.225 | |
| GAST | 0870Ref. AB992B | — | 26.19375 | |
| GAST | 1022Ref. AB992B | — | 26.19375 | |
| GAST | 1023Ref. AK513 | 38 | 25.4 | |
| GAST | 1031Ref. AD979 | — | 9.128125 | |
| GAST | 1032Ref. AD979 | — | 9.128125 | |
| GAST | 1033Ref. AD979 | — | 9.128125 | |
| GAST | 1034Ref. AD979 | — | 9.128125 | |
| GAST | 1040Ref. AB992B | — | 26.19375 | |
| GAST | 1423Ref. AL284 | — | 25.4 | |
| GAST | 1531Ref. AD979 | — | 9.525 | |
| GAST | 1532Ref. AD979 | — | 9.525 | |
| GAST | 1533Ref. AD979 | — | 9.525 | |
| GAST | 1534Ref. AD979 | — | 9.525 | |
| GAST | 2031Ref. AJ652A | — | 11.1125 | |
| GAST | 2032Ref. AJ652A | — | 11.1125 | |
| GAST | 2033Ref. AJ652A | — | 11.1125 | |
| GAST | 2035Ref. AJ958 | — | 11.509375 | |
| GAST | 3031Ref. AJ958 | — | 11.509375 | |
| GAST | 3032Ref. AJ958 | — | 11.509375 | |
| GAST | 3033Ref. AJ958 | — | 11.509375 | |
| DuraVane | RVD002L | 22 | 14 | |
| DuraVane | RVD004L | 26 | 19 | |
| DuraVane | RVD007L | — | 27 | |
| DuraVane | RVD012L | 42 | 32 | |
| DuraVane | RVD018LRef. 3301016 | 42 | — | |
| DuraVane | RVD028L | 43 | 33 | |
| DuraVane | RVD040L | 46 | 36 | |
| DuraVane | RVD060L | 46 | 36 | |
| DuraVane | RVD075L | 46 | 41 | |
| Heidelberg | Rietschle DLT 6Ref. 22.102.1311 · 513878 | 31 | 20 | |
| Heidelberg | Rietschle VLT 6Ref. 22.102.1311 · 513878 | 31 | 20 | |
| Heidelberg | Rietschle TL 6 / TLV 6Ref. 22.102.1311 · 513878 | 31 | — | |
| Heidelberg | BECKER VT 4.16Ref. 61.164.1737 · 90134700007 | 35 | 21 | |
| Heidelberg | BECKER DT 4.16Ref. 61.164.1737 · 90134700007 | 35 | 21 | |
| Heidelberg | BECKER T 3.16 DSKRef. 61.164.1737 · 90134700007 | 35 | 21 | |
| Heidelberg | BECKER VT 4.40Ref. S9.164.1453 / S.9.164.1453 · 90135200007 | 43 | 28 | |
| Heidelberg | BECKER DT 4.40Ref. S9.164.1453 / S.9.164.1453 · 90135200007 | 43 | 28 | |
| Heidelberg | BECKER T 4.40 DSKRef. S9.164.1453 / S.9.164.1453 · 90135200007 | 43 | 28 | |
| Heidelberg | Rietschle DLT 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle VLT 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-DTN 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-DTN 16Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-VTN 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-VTN 16Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-KTN 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle KLT 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle V-KTN 16Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | 24 | |
| Heidelberg | Rietschle TL 15 / TLV 15Ref. G2.102.1951 / L4.164.1563 · 513702 | 39 | — | |
| Heidelberg | Rietschle V-KTA 80/5Ref. 91.102.2021 · 528401 | 43 | 38 | |
| Heidelberg | Rietschle V-DTA 80Ref. M2.102.2021 · 523778 / 526886 / 523851 | 52 | 38 | |
| Heidelberg | Rietschle V-KTA 80/1Ref. M2.102.2021 · 523778 / 526886 / 523851 | 52 | 38 | |
| Heidelberg | Rietschle V-KTA 80/2Ref. M2.102.2021 · 523778 / 526886 / 523851 | 52 | 38 | |
| Heidelberg | Rietschle V-KTA 80/3Ref. M2.102.2021 · 523778 / 526886 / 523851 | 52 | 38 | |
| Heidelberg | Rietschle KTA 80/4Ref. M2.102.2021 · 523778 / 526886 / 523851 | 52 | 38 | |
| Heidelberg | Rietschle TLV 3Ref. 00.780.3168 · 507051 | 15 | — | |
| Heidelberg | Rietschle TR 25 DV / TR 26 DVRef. 00.591.0470 · 513431 | 39 | — | |
| Heidelberg | Rietschle TR 60 DV / TR 61 DVRef. 00.591.0011 · 515642 | 51 | — | |
| Heidelberg | Rietschle TR 80 DVV / TR 81 DVVRef. 51.102.1451 · 526311 | 59 | — | |
| Republic | DRT 410Ref. 5310000 | — | 27.0002 | |
| Republic | DRT 416Ref. 5310001 | 35.5 | 27.0002 | |
| Republic | DRT 425KRef. 5310002 | 43 | 32.9946 | |
| Republic | DRT 440KRef. 5310003 | 43 | 32.9946 | |
| Republic | DVT 410 | — | 27.0002 | |
| Republic | DVT 416Ref. 5310001 | 35.5 | 27.0002 | |
| Republic | DVT 425KRef. 5310002 | 43 | 32.9946 | |
| Republic | DVT 440KRef. 5310003 | 43 | 32.9946 | |
| Republic | VRT 410Ref. 5310000 | — | 27.0002 | |
| Republic | VRT 416Ref. 5310001 | 35.5 | 27.0002 | |
| Republic | VRT 425Ref. 5310002 | 43 | 32.9946 | |
| Republic | VRT 440Ref. 5310003 | 43 | 32.9946 | |
| Schmalz | EVE-TR 4Ref. 10.03.01.00108 | 16 | 11 | |
| Schmalz | EVE-TR 4 DCRef. 10.03.01.00108 | — | 11 | |
| Schmalz | EVE-TR 8Ref. 10.03.01.00109 | 18.5 | 12.5 | |
| Schmalz | EVE-TR 8 DCRef. 10.03.01.00109 | — | 12.5 | |
| Schmalz | EVE-TR 10Ref. 10.03.01.00132 | 27 | 18 | |
| Schmalz | EVE-TR 16Ref. 10.03.01.00133 | 35.5 | 21 | |
| Schmalz | EVE-TR 25Ref. 10.03.01.00134 | 43 | 28 | |
| Schmalz | EVE-TR 40Ref. 10.03.01.00135 | 43 | 28 | |
| Schmalz | EVE-TR 50 | — | 33 | |
| Schmalz | EVE-TR 60Ref. 22.09.01.00031 | 39 | 21 | |
| Schmalz | EVE-TR 80Ref. 22.09.01.00031 | 39 | 26 | |
| Schmalz | EVE-TR 100Ref. 22.09.01.00033 | 39 | 26 | |
| Schmalz | EVE-TR 140Ref. 22.09.01.00035 | 48 | 31 | |
| Schmalz | EVE-TR-X 10 | — | 18 | |
| Schmalz | EVE-TR-X 16Ref. 10.03.01.00224 | 34 | 21 | |
| Schmalz | EVE-TR-X 25Ref. 10.03.01.00225 | 41 | 28 | |
| Schmalz | EVE-TR-X 40Ref. 10.03.01.00226 | 41 | 28 | |
| Schmalz | EVE-TR-X 80Ref. 10.03.01.00227 | 37 | 26 | |
| Schmalz | EVE-TR-X 100 | — | 26 | |
| Schmalz | EVE-TR-X 140 | — | 31 |
We could not find that model or part number
Check the reference on the nameplate. If it is not in this table, you can enter the data from its manual in the checker.
291 records include a documented minimum and 247 include both heights. A dash means that measurement is still to be confirmed. If the minimum is missing, enter it only from the manual for your exact model.
The suffix changes the limit: standard VT 4.40, 28 mm; VT 4.40/0-90, 33 mm. Select the exact variant. Need to identify your vanes?
Reference documentation
Check the edition, model and variant of your equipment before using a limit
BECKER
The BECKER table of 15/09/2022 documents height and original set. The earlier VT, DT and T series and the DXLF family are completed with manuals and data sheets for the specific part number. On the VT 4.40/0-90, check the index on the nameplate.
View references (4)
- BECKER graphite vane table · 15/09/2022
- VT/VX manual · variant /0-90
- BECKER DXLF 2.400 / 2.500 · manual, p. 5
- BECKER DVX 3.140 · instructions, A max./min. and set 90140500007
BUSCH SECO
SV stands for vacuum, SD for pressure and DC for pressure and vacuum. Limits are linked to the manual edition and the corresponding material. Check the C or D suffix and the ZIRKON or NIOB version in particular.
View references (8)
- BUSCH SECO SV/SD 1010–1025 C and 1040 D manual · p. 18
- BUSCH SECO SV 1010–1040 C/D documentation
- BUSCH manual 0870135648 · vane check
- Original Aerodur Zirkon part numbers · Busch
- BUSCH SECO SV 1003/1005 D · manual, §7.2
- BUSCH 0870569132 · SV/SD 1040 C and DC edition, p. 14
- BUSCH SECO SV/SD 1063 and 1080 B · vane inspection
- BUSCH SV/SD 1010–1040 B · manual, fig. 7.2
Elmo Rietschle
Limits are taken from each series’ manual. The new height is cross-checked against the spare-part catalogue. On the V-KTA 80/5, vane 528401 measures 43 mm when new and the manual threshold is 38 mm.
View references (15)
- Elmo Rietschle manual BA 187 · V-VTE 3–10, p. 49
- Catalogue of original vanes · Ehrler & Beck
- Elmo Rietschle manual BA 280-EN · p. 22
- Elmo Rietschle manual BA 250-DE · §7.2.2
- Elmo Rietschle V-VTR manual · §7.2.2
- Rietschle VTB manual · vane inspection
- Rietschle VFT manual · vane inspection
- Elmo Rietschle BA 387-EN · V-DTE, p. 21
- Elmo Rietschle BA 380-EN · V-DTN, p. 21
- Rietschle DLT 6–40 · manual, section 2
- Rietschle VLT 6–60 · manual, section 2
- Elmo Rietschle BA 450-EN · V-KTA, §7.2.2
- Original vane sets and maintenance · Elmo Rietschle
- Rietschle manual BE 480 · KLT 10/15/25/40, p. 11
- Elmo Rietschle manual BA 481 DE/FR · V-KTN 16/26/41, §7.2.2
ORION
New height and spare-part numbers. For KRF40A-V-01 the data sheet sets replacement intervals according to the operating vacuum.
View references (3)
- ORION KRF40A-V-01 · specification and replacement periods
- ORION · original set 04106205010, dimensions and applications
- ORION KRF15A/25A/40A · manual, spare parts by version
DVP
The SB and SC series manuals give the limit for dimension A and distinguish the TV variants.
View references (4)
- DVP · SC/SB manual, §6.2.3
- DVP · SC 16/25/40 manual, §6.2.3
- DVP · spare-part dimension sheets, Supervane
- DVP Pumps · vane references by model, parts catalogue
GAST
The limits apply to oil-free direct-drive units. The manual’s figures are in inches and are converted to millimetres.
View references (2)
- GAST · direct-drive service table, manufacturer’s copy
- GAST 23 series, oil-free · parts breakdown, part numbers AH850A and AK513
DuraVane
Data for the Dekker RVD dry-running series. The RVD018L is listed with its new height; its minimum must be confirmed in the unit’s manual.
View references (3)
- Dekker DuraVane RVD · manual, Minimum Vane Dimensions table
- DuraVane RVD/RCD · CP Grafite dimension sheet
- Dekker RVD018L · parts breakdown, vane 3301016
Heidelberg
On a Heidelberg press, identify the manufacturer and full model on the pump nameplate. Search by Heidelberg or manufacturer part number and select the matching model. The wear minimum is taken from that pump’s manual.
View references (3)
- Heidelberg spare-part equivalence catalogue
- Heidelberg 22.102.1311 · dimension sheet and Rietschle 513878 equivalent
- Rietschle manual BE 458 · KTA /4, vane check
Republic
The manual covers the VRT, DRT and DVT series from 410 to 440. The table converts the inch limits to millimetres.
View references (2)
- Republic · VRT/DRT/DVT 410–440 manual, p. 8
- Republic · dimension sheet by model and part number
Schmalz
The EVE-TR manuals publish limits by size. Check whether the nameplate shows the standard, DC or -X version.
View references (3)
- Schmalz EVE-TR 4/8 · 30.30.01.00130, §10.4.3
- Schmalz EVE-TR 10–50 · 30.30.01.00556, p. 40
- Schmalz EVE-TR 60–140 · 30.30.01.00770, p. 40
Document review: . The limits apply to the equipment and documents cited. Confirm the edition applicable to your unit. Matching dimensions do not establish spare-part compatibility or material equivalence
Before you decide
Height is one part of the inspection. These answers help you interpret the measurement and understand its scope
What does a 50% margin mean?
Half of the range between the new height and the minimum remains. On the standard VT 4.40 that range is 15 mm: a measurement of 35.5 mm leaves 7.5 mm to the 28 mm limit. The percentage describes a dimension. 100% only indicates that the height matches the new reference; it does not prove that the part is new or allow remaining hours to be calculated.
Why can I get millimetres without a percentage?
To compare with the minimum, the measured height and the model limit are enough. The percentage also needs the new height. When the new height is shown as pending, you can add it if you have the documented value for the exact part number.
What can you conclude from the result?
“Margin available” means the height is above the minimum. “At the limit” indicates that it has reached it; “Below minimum”, that it has fallen below it. In these last two cases, follow the replacement criteria in the manual. The indicator stops at 0 mm and, where it can be calculated, at 0%; the text keeps the actual shortfall. Always complete the inspection for cracks, chipping and uneven wear, even if there is margin. Broken, cracked or damaged vanes must be replaced even if they still have enough height: a vane that breaks can damage the cylinder and the rotor.
When should I measure or replace the vanes?
Apply the inspection interval in the manual for the model, configuration and installed material. If any vane reaches or falls below the minimum, follow the replacement criteria in the manual. Intervals for an original material do not automatically carry over to another material or manufacturer. Operating conditions and maintenance have an influence; the percentage from this tool does not set an inspection or replacement date.
Can I use the limit of a similar model?
The full designation matters: standard VT 4.40 uses 28 mm and VT 4.40/0-90, 33 mm. The vane part number alone does not always determine the minimum either; the BECKER table assigns it by equipment. A dimensional match does not establish compatibility. If your variant is not listed, use its manual or ask before interpreting the result.
Which measurement do I use if the pieces differ?
Record each vane and use the lowest reading in the set, without averaging. Enter as many decimals as your instrument can resolve, with a comma or point, without rounding up. If the reading is close to the minimum, verify the measurement and apply the manual’s criteria. The calculation does not include instrument uncertainty or set a safety tolerance between pieces.
Does a loss of performance prove wear?
A loss of vacuum or pressure can have other causes, such as clogged filters or leaks. Compare the height and follow the diagnostic procedure in your equipment’s manual. This checker does not measure vacuum, pressure, tightness or temperature.
Do the images represent all models?
The views are renders created from textures of real photographs of the HARDVANES H95434 vane, 95 × 43 × 4 mm, and its set of seven pieces. They are reference visualisations of the surface, the edges and the longitudinal bevel. Dimensions, profiles, grooves and finishes vary by part number. The vane in the sequence and in the checker was created from those photographs and represents relative height. The dimensions and minimum for each unit come from its documentation.
What do I need if my equipment is not listed?
Manual mode is for equipment whose manual specifies a minimum vane height (in some documents, minimum vane width). Select the brand, then enter the full model, that minimum and your measurement. The new height also gives you the percentage. If the brand is missing or you do not have enough documentation, ask HARDVANES about your model.
Unsure about your model?
Send us a legible photo of the nameplate, the variant and the part number of the installed vanes