Skip to content
The 3D vacuum pump with a transparent cover: the off-centre rotor and the six graphite vanes
01

Know your pump

The rotor turns off-centre inside the cylinder, and centrifugal force throws the vanes out against the wall. Before opening up, note down the make, model, variant and serial number, locate the direction-of-rotation arrow and keep the manual to hand.

Matching dimensions are not enough: the pump reference determines the replacement part.
02

Stop and lock out

Main switch to 0, plug pulled out, padlock and tag. Check that no voltage is present, release any remaining vacuum and let the cylinder cool down.

The stop button does not isolate the machine.
03

Remove the screws

Loosen the cover screws with the Allen key in a criss-cross sequence and keep them together in a magnetic tray.

No prying and no hammering on the mating surfaces.
04

Take off the cover

Pull it straight off without touching the rotor, and lay it on a clean cloth with the gasket facing up. Work on a clean, stable, protected bench.

Use the extraction points provided by the manufacturer.
05

Take out the used vanes

Pull them out one at a time in an axial direction and note which way the bevel was facing: the new ones go in the same way, toward the direction of rotation.

If one sticks, stop and check the slot; never pull it with pliers.
06

Measure the wear

Use the digital caliper to measure the height of a used vane and of a new one, and compare with the manufacturer's minimum dimension. Also look for cracks, chips or uneven wear. How to compare

If one is below the minimum, replace the complete set.
07

Blow out and wipe

Blow out the rotor slots, the cylinder and the cover with dry compressed air. Then run a clean, dry cloth over the rotor face, the cylinder rim and the bottom until no graphite residue or dirt remains.

Safety glasses and a dust mask: graphite dust is very fine.
08

Check slots, cylinder and cover

Shine a light into each slot in turn: no fragment or object may remain. Under raking light, inspect the cylinder and the inner face of the cover: no scratches, grooves, steps or burrs. What to look for

If a vane has broken, find every fragment before you continue.
09

Fit the new vanes

Check the direction-of-rotation arrow. Each vane goes in with the bevel facing outward, against the cylinder, and facing the direction of rotation. The vanes must slide in their slots without being forced.

With the bevel the wrong way round, the vane breaks.
10

Close the cover

Check the gasket, seat the cover on its dowel pins and tighten the screws crosswise, gradually, to the torque specified by the manufacturer.

If the cover does not seat, do not force it down with the screws.
11

Reconnect and test

With the guards in place, remove the padlock, plug in and set the switch to I. Check direction of rotation, noise, vibration, temperature and vacuum, and record the date, operating hours, part reference and measurements.

Observe the running-in period specified in your model's manual.
Scroll and the pump comes apart

Dry-running rotary vane vacuum pump Vane replacement
Step by step

The HARDVANES guide to replacing the graphite vanes of a dry-running rotary vacuum pump without breaking a single one. Scroll: the pump comes apart and goes back together as you go.

The HARDVANES guide to replacing the carbon-graphite vanes of a dry-running vacuum pump without breaking a single one: eleven steps, one rule with no exceptions and a one-minute 3D guide.

The bevel, toward the direction of rotation.Fitted the wrong way round, the vane breaks.
Dry, always.No oil or grease on the vanes or in the chamber.
If it doesn't slide, stop.Forcing never fixes a wrong assembly.

This applies to any dry-running rotary vane vacuum pump, also known as a vane exhauster or rotary vane blower: the carbon-graphite vanes (also called rotor vanes, sliding vanes or blades) are replaced the same way on a Becker, Rietschle, Busch, Orion or DVP. Find the ones for your model in the catalogue by brand.

What you need
before you open it

Eight things on the bench and the pump locked out. With these you can carry out a complete vane replacement on a dry-running rotary vacuum pump, from the cover to start-up.

  • HARDVANES vane setMirror-finish carbon-graphite, to your pump's reference.
  • Digital caliperTo measure the height of each vane to a hundredth of a millimetre.
  • Allen keyThe right size for the cover screws.
  • Dry compressed airA blow gun, with air free of oil and water.
  • LED torchWhite light for checking slot by slot.
  • Magnifier and tweezersTo spot and pick out any debris.
  • Clean clothTo wipe off graphite residue after the air, and to rest the cover on.
  • Padlock and tagTo lock out the power while you work.

Mirror finish
Engraved on the edge

HARDVANES carbon-graphite vanes leave the factory with a mirror finish and laser engraving on the edge opposite the bevel, always starting from the left end: brand, reference and ESP. So you know exactly what you are fitting, and you always reorder the same set.

New HARDVANES carbon-graphite vane with a mirror finish on a black stand: golden light reflects off the polished face, and the edge is engraved, starting from the left end, with HARDVANES ® H122X34X5 ESP
HARDVANES ® H122X34X5 ESPReference H length × height × thickness in mm. ESP: made in Spain.

The bevel, always
toward the direction of rotation

It is the mistake that breaks more vanes than any other. Each vane goes in with the bevel facing outward, against the cylinder, and angled toward the way the rotor turns. That way the contact edge trails and the vane slides. The wrong way round, it digs into the wall and breaks.

The bevel faces the rotation: the vane slides against the cylinder. The rotor turns against the bevel: the edge digs in and the vane breaks.

Close-up of the tip of a graphite vane resting on the pump's honed cylinder: the bevel, highlighted in gold, faces the direction of rotation
The tip against the cylinder. The bevelled edge leads and the contact edge trails: the vane glides over the wall instead of catching on it.
  1. Find the arrow on the housingIt shows which way the rotor turns. If you can't find it, check the nameplate or the manual before opening up.
  2. Bevel outward, against the cylinderThe bevelled edge is the one that rubs against the wall. The base, with the HARDVANES engraving on the left of its edge, goes to the bottom of the slot.
  3. Angled toward the direction of rotationThe bevel face points the way the vane travels. Check all six before closing.

Explore it at your own pace
Rotate, pause and replay

The same animation with its controls: jump to any step, rotate the view with your finger or mouse and watch it in slow motion where it matters.

11 steps with explanations Free view: drag to rotate 1 min 08 s Open full screen

How worn are they?
Stand them side by side

A vane wears in height and in thickness too. Stand it next to a new one and measure both with the digital caliper: the used one is shorter and thinner, and its bevel is rounded and chipped.

Two graphite vanes standing on a black stand: on the left a new HARDVANES vane with a mirror finish, 34.0 mm high and 5.0 mm thick; on the right a used, matt one, 27.2 mm and 4.6 mm, with a worn bevel
Height
−6.8 mmfrom 34.0 to 27.2 mm · 20%
Thickness
−0.4 mmfrom 5.0 to 4.6 mm: more play in the slot
Bevel
Roundedand chipped: it no longer seats against the cylinder
  • Use the digital caliper to measure height and thickness at both ends and in the centre of each vane. The lowest reading is the one that counts.
  • Compare with the manufacturer's minimum dimension. No single height or number of operating hours applies to every pump.
  • If one vane is below the minimum, replace the complete set. Do not mix new and used vanes.
  • Record each vane's measurement and the operating hours: that way you will know how fast they wear.

Example values. Use the figure for your model.

Cylinder and cover
No scratches, no surprises

With the vanes out, this is the moment to look at the surfaces they slide on. A scratch in the cylinder files down the tip of the new vane; a scratched or warped cover drags on the vane edges and holds them back in the slot. Inspect both before reassembly.

Inside of a vacuum pump cylinder under raking light: circumferential scratches, a deep groove and a step in the honed surface

The cylinder

Inside, it should look uniform, with only the fine cross-hatch of the honed finish.

What to look for

  • Scratches or grooves running around the cylinder, in the direction of rotation.
  • Steps or a pronounced ridge where the vane travel ends.
  • Uneven shiny or dull patches and seizure marks.
  • Rust, pitting or embedded graphite residue.

How to check it

  • With the cylinder clean and dry, shine the LED torch at a low angle, almost parallel to the wall: scratches show up as lines of light and shadow.
  • Run your fingernail across the scratch: if it catches, it is a deep groove.
  • Go over the whole cylinder, not just the part you can see. Use the magnifier to look for raised metal.

What to do

  • Fine marks you can't feel with a fingernail: follow the criteria in your pump's manual.
  • Grooves you can feel with a fingernail, steps or ovality: do not fit new vanes. Have the cylinder inspected; the manufacturer will say whether it can be re-machined or must be replaced.
  • Find the cause: fragments of a broken vane, dirt drawn in through the inlet, or damaged filters.
Inner face of a vacuum pump cover with circular scratches left by the vane edges and a deep groove

The cover

The vane edges rub against its inner face on every revolution: it must be smooth and flat.

What to look for

  • Circular scratches or grooves where the vane edges rub.
  • Burrs or dents on the inner face and around the edges.
  • A warped face, or one that does not sit flat.
  • Remains of old gasket, rust or caked-on dirt.

How to check it

  • Raking light across the inner face, turning the cover as you go.
  • Lay a precision straightedge across it in several directions: if light shows underneath, it is not flat.
  • Your fingernail over the scratches, and a look at the gasket and the locating dowels.

What to do

  • Clean it without scratching the metal: no abrasive paper and no metal scrapers.
  • If there are grooves, burrs or warping, have the cover inspected or replaced.
  • Never correct a warped cover by tightening the screws harder.

A scratched or warped cover can jam the vanes in their slots. The vane stops extending, the pump loses vacuum and breakage can follow. On damaged surfaces, a new vane will not last long.

Avoid these
breakages

Carbon-graphite is hard and self-lubricating, but it does not forgive knocks or forced assembly. Almost every breakage starts with one of these eight oversights, and the first is the most common.

Bevel the wrong way round

Against the direction of rotation, the edge strikes the cylinder wall and the vane breaks. It is the most common breakage and the easiest to avoid: check the arrow before fitting.

Knocks and drops

Graphite chips. Work on a protected surface and never use a vane as a lever.

Oil or grease

No oil, grease or sprays on the vanes or in the chamber of a dry-running pump.

Sanding it to fit

Changing the thickness, the edges or the bevel alters the fit. If it doesn't slide, check the reference, cleanliness and the rotor.

Fitting with debris inside

Dust, metal chips or fragments of the old vane can jam the rotor. Check the filters too.

Ignoring wear

Compare with the minimum dimension and replace in time. Don't wait for a vane to break.

Excess heat

Blocked grilles, clogged filters or operating outside the limits. A replacement part won't fix the cause.

Mixing parts

Confirm material, reference and number of vanes, and replace the complete set when the manufacturer requires it.

Fragment of a broken graphite vane, with sharp fracture edges, lodged in a rotor slot of a vacuum pump

Has a vane
broken?
Don't start it

A loose piece of graphite inside the cylinder can jam the rotor and wreck the pump as soon as it turns again.

  1. Stop and isolate the pump: switch to 0, plug pulled out, padlock on.
  2. Keep all the fragments and photograph the damaged surfaces.
  3. Have the rotor, cylinder and covers inspected, and the cause of the breakage found.
  4. Put it back into service only after the repair and the checks required for your model.

Keep them
turning

Clean air
Check filters and seals as often as the dust in your process demands.
Unobstructed cooling
Grilles, fan and fins kept clear so the pump can dissipate its heat.
No liquids inside
No water, condensate or oil in the chamber unless the equipment is designed for it.
Within its limits
Monitor vacuum or pressure, and temperature. Do not tamper with the safety valves.
Wear on record
Measure and record the height of each vane at every inspection.
Mechanically sound
Clearances, bearings, covers and drive matter too. Diagnosis is a job for qualified personnel.
Spares protected
Store the vanes in their box: dry, clean and safe from knocks.
After a long shutdown
Follow the start-up procedure: the vanes may have stuck.

There are no universal intervals. Follow the inspection hours and wear limit for your model; with dust, heavy loads or heat, inspect more often.

Double-check
the assembly

Tick each point before restoring power. Your progress is saved in this browser.

0of 8 checked

Checks still outstanding.

The list helps you not to forget anything; it does not replace the checks in your pump's manual.

Your questions
answered

Which way does the bevel go?

Always toward the rotor's direction of rotation. Check the arrow on the housing and fit each vane with the bevel facing outward, against the cylinder, angled the way the rotor turns. The wrong way round, the edge strikes the wall and the vane breaks.

Can I replace them myself?

Yes, if you have the training, the tools and the authorisation, and your pump's manual allows it. Electrical work and anything beyond this maintenance task must be done by qualified personnel.

Should the vanes be greased?

No. In dry-running pumps, neither the carbon-graphite vanes nor the chamber take any oil or grease. The bearings may need grease: check the pump manual. If your pump is lubricated or you don't know how it runs, identify it first from its nameplate.

What if a vane won't go in?

Stop. Check dimensions, reference, bevel orientation, cleanliness and the condition of the slot. Do not hammer, sand or force it. If it still won't go in, ask for a technical inspection.

Do I replace one vane or the whole set?

Follow the specification of your equipment and of the replacement part. When the complete set is due, do not mix new and used vanes. After a breakage, also investigate the cause and any damage to the whole unit.

When are they worn out?

When they reach the wear limit set by the manufacturer of your model, or sooner if they show cracks, chips or uneven wear. There is no minimum height or service life in hours that applies to every pump.

Can I clean them with solvent?

Only if your pump's manual approves both the product and the method; some manufacturers prohibit it. Never leave the vanes to soak.

How long does running-in take?

It depends on the model: follow its manual. During running-in, stop the pump if you notice abnormal noise, vibration or temperature.

What should I clean the cylinder and rotor with?

First with dry compressed air, free of oil and water, then with a clean, dry, lint-free cloth: rotor face, cylinder rim and bottom. Do not use solvents unless your pump's manual approves them.

Where is the engraving on a HARDVANES vane?

On the edge opposite the bevel, always starting from the left end: HARDVANES ®, the reference (for example H122X34X5: length × height × thickness in mm) and ESP, made in Spain. That edge goes to the bottom of the slot.

Can I fit new vanes if the cylinder or cover is scratched?

If they are fine marks you can't feel with a fingernail, follow the criteria in your pump's manual. If your nail catches, if there are steps or burrs, or if the cover does not sit flat, no: the new vane would wear out quickly or jam in its slot. Have the cylinder and cover inspected, and find the cause of the scratches.

00.20.40.60.81HARDVANESbar abs
Vacuum gauge100% of rated vacuum
00.511.522.5HARDVANESbar
Pressure gauge100% of rated pressure

HARDVANES

Result: your pump, back to 100% performance.

Worn vanes give no warning: the pump keeps turning, but it no longer delivers 100%.

Worn vanes

It loses vacuum and pressure, and takes longer to do the same job.

New vanes

Factory vacuum and pressure are back: 100% performance.

Find your vanes With the cylinder, rotor and the rest of the pump in good condition.
The pump closed and running in the studio, with the golden direction-of-rotation arrow

Your model
Your replacement

Send us the pump nameplate, the reference or a photo of the vanes and we will tell you which ones you need.

sales@hardvanes.com +34 685 090 732